Volunteer Audio

Kicker – 44KXMA12002

$729.95

2 Channel Amp
  • 1200W Maximum Power with 300W RMS
  • Preamp Outputs
  • Class D amp technology
  • More Features!

5 in stock

Description

Product Description

Kicker 44KXMA12002

 

AMPLIFIER FEATURES

Powerful, dependable, and good-looking

Kicker’s KXMA400.4 marine 4-channel amplifier will bring brilliance and clarity to your sound, powering four speakers with 50 watts RMS each. This reliable and compact KXM Series rocker will run cool even when pushed hard, thanks to its high-mass heatsink, high-tech internal components, and efficient full-range Class-D amp technology. Building a big system piece-by-piece? You could start by using this amp in 2-channel mode to drive a couple subs with 200 watts each, and then later switch the amp back to 4-channel mode to power your speakers when you get a bigger amp for the subs.

Made for marine use

The KXMA400.4 features a conformal coated circuit board for improved water and dust resistance, plus corrosion-resistant power connections, a gasket-sealed front cover, and stainless steel mounting hardware that won’t rust all over your boat’s gel coat or carpeting.

Connection perfection

Kicker employs their Fail-Safe Integration Technology (FIT2™) to reject noise and stop any interference generated by your boat’s electronics, so you’ll enjoy your music clean and pure. Speaker-level inputs make it possible to hook this amp up to almost any stereo receiver or radio. Kicker also helps you set this amp’s gain properly, by offering free test tones for downloading. You play a tone and turn the gain up until the gain knob glows red. Then, you turn it down until it just goes out, and the amp’s gain is set perfectly.

Versatile controls behind the folding door

A gasket-sealed front door gives you quick and easy access to your amp’s controls. You can tune for almost any kind of speaker, as the steeply-sloped high- and low-pass filters offer a wide range of adjustment. The filter section for the Amp 2 channels can be set up for bandpass operation — where both the high- and low-pass filters are engaged to allow only the frequencies between them to play — for optimizing the signal for midrange speakers in a 3-way system.

Amplifier Specifications

AMPLIFIER SPECIFICATIONS

Kicker 44KXMA12002

FEATURES
Amplifier Class D
CEA-2006 Compliant Yes
Crossover Low-Pass Crossover Frequency Variable Low-pass 40Hz-500Hz
Low-Pass Slope (dB/octave) 24 dB/octave
High-Pass Crossover Frequency Variable High-pass 10Hz-500Hz
High-Pass Slope (dB/octave) 24 dB/octave
Cooling System Heat Sink
Fuse Rating 150
Speaker Level Inputs No
Preamp Outputs Yes
Dimensions (L X W X H) 11-3/16 x 8-5/16 x 2-1/8
Compatable Wiring Kits PK4, CK4
Warranty 2 Year
POWER RATINGS
POWER OUTPUT RMS Power Output
(Watts x Channels)
300W
Peak Power Output
(Watts x Channels)
1200W
Bridged Power
(Watts x Channels)
N/A
Minimum Impedance Bridged Not Bridgable
Unbridged 2 Ohm
Signal To Noise (S/N) 95DB
THD at Rated RMS Power 1%
Frequency Response 10Hz – 20kHz
Input Voltage 14.4V (10V-16V)
Wire Input Gauge 4 Gauge

Additional information

Weight 8 lbs
Dimensions 17.00 × 4.50 × 11.00 in
Brand

Kicker

Min Impedance Unbridged

2 Ohm

Maximum Wattage

1200W

Type

2 Channel Amp

RMS Wattage

300W

Amplifier Class

D

1